The Track Saw Forum  

Go Back   The Track Saw Forum > Search Forums

Showing results 1 to 15 of 15
Search took 0.02 seconds.
Search: Posts Made By: jbrewton
Forum: Router Guide Systems 03-22-2016, 12:35 PM
Replies: 5
Views: 2,741
Posted By jbrewton
Takes some pictures and lets us know how it goes....

Takes some pictures and lets us know how it goes. I am interested in do the same thing.
Forum: Material Support Systems 03-21-2016, 12:16 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Thanks Dik, I will be making the...

Thanks Dik,

I will be making the modification tonight.
Forum: Material Support Systems 03-21-2016, 09:42 AM
Replies: 33
Views: 7,625
Posted By jbrewton
Dik, The set up video says make the mounts...

Dik,

The set up video says make the mounts should be flush. Is the video incorrect? Is this a case where real world application does not follow the book theory? Thanks for the helpful tip.
...
Forum: Router Guide Systems 03-17-2016, 12:31 PM
Replies: 3
Views: 3,129
Posted By jbrewton
bumpnstump, Thanks you for the details about...

bumpnstump,

Thanks you for the details about your setup. Looks a lot like what I did, however your's is much more simple. Any reason why you route on the left side of the guild track? Love your...
Forum: Router Guide Systems 03-16-2016, 01:32 PM
Replies: 3
Views: 3,129
Posted By jbrewton
Drawer Making

Last week I used the SSRK system to route some groves and rabbits for making drawer. I started off by inserting 3/4" ply into the rails. Using the SSRK, I 1/6 inch groove on the right edge of the...
Forum: Material Support Systems 03-14-2016, 11:00 AM
Replies: 33
Views: 7,625
Posted By jbrewton
Thanks Tracedfar. I have started using inserts...

Thanks Tracedfar. I have started using inserts and found that helps a lot. If the blade does not indicated full kerf, what should I assume? using Diablo's from Home depot
...
Forum: Material Support Systems 03-09-2016, 10:54 AM
Replies: 33
Views: 7,625
Posted By jbrewton
Thanks Dik.

Thanks Dik.
Forum: Woodworking Software 03-09-2016, 10:52 AM
Replies: 6
Views: 4,593
Posted By jbrewton
Mad Mac, I have used the App. Great for the...

Mad Mac,

I have used the App. Great for the shop if you don't print out the report.
Forum: Material Support Systems 03-08-2016, 04:54 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Mike, When you "ride it over" with sand paper...

Mike, When you "ride it over" with sand paper are you say to sand the cut edge (Side) of the ACE? or the Bottom of the ACE?
Forum: Woodworking Software 03-08-2016, 10:51 AM
Replies: 6
Views: 4,593
Posted By jbrewton
Cutlist FX

I used sketchup to create my cut list for a while. You know, create a component called plywood, then start moving the parts, rotate flip then try to get them on the same plane to lay on the plywood...
Forum: Material Support Systems 03-04-2016, 06:14 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Thanks Mike, I will try that if the bevel showed...

Thanks Mike, I will try that if the bevel showed up again. I also check my miter saw that I have had for over 6 years and found that it was also not square. I was doing more 2x4 construction so it...
Forum: Material Support Systems 03-04-2016, 03:06 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Some findings: So I have tried a few things to...

Some findings:
So I have tried a few things to try to keep my material still during the route. I would clamp a piece of scrap on each side of the material perpendicular to the router cut. What I...
Forum: Material Support Systems 03-02-2016, 12:19 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Thank you all for the feed back. I did as Dik...

Thank you all for the feed back. I did as Dik suggested and the guide was laying perfectly flat on the rails. Never thought about aluminum and sawdust, thanks aaronp for the tip to hold the material...
Forum: Material Support Systems 03-01-2016, 03:18 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Thanks Dik. I will check to see if the track...

Thanks Dik. I will check to see if the track lays flat. If it is not, I will adjust as you indicated. BTW, I meant to say "flush with side fence" instead of edge of first rail, but I could not...
Forum: Material Support Systems 03-01-2016, 01:31 PM
Replies: 33
Views: 7,625
Posted By jbrewton
Material Moving

Purchased the EZ-one workbench recently and I am having issues with material moving (causing cuts to not be squared). When I let the track fall on the material, the forward movement of the track...
Showing results 1 to 15 of 15

 
Forum Jump

All times are GMT -3. The time now is 10:26 AM.


Powered by vBulletin® Version 3.8.4
Copyright ©2000 - 2018, Jelsoft Enterprises Ltd.